← back// Wire EDM — Part Pickup Generator

( WIRE DIA 0.0100" WIRE RADIUS 0.0050" BACK-OFF 0.1000" )   ( OP 1: HOLE CENTER PICKUP — DIA 1.0000" 2 PASSES )   ( MOVE TO START POSITION X0.0000 Y0.0000 ) G90 G00 X0.0000 Y0.0000   ( THREAD WIRE ) T91   ( PASS 1/2 — TOUCH X- ) G80 X- ( SET X0 AT THIS SURFACE — NO RADIUS COMP, G192X WILL HALVE LATER ) G92 X0.0000 ( DISABLE SENSING + BACK OFF X+0.1000" ) M05 G91 G00 X+0.1000 G90 ( RAPID TO OPPOSITE SIDE: HOLE DIA 1.0000" - BACK OFF 0.1000" = 0.9000" ) G00 X0.9000   ( PASS 1/2 — TOUCH X+ ) G80 X+ ( G192X SETS X TO HALF OF CURRENT X VALUE — WIRE CENTER ) G192 X ( DISABLE SENSING + BACK OFF X-0.1000" ) M05 G91 G00 X-0.1000 G90 G00 X0.0000   ( PASS 1/2 — TOUCH Y- ) G80 Y- ( SET Y0 AT THIS SURFACE — NO RADIUS COMP, G192Y WILL HALVE LATER ) G92 Y0.0000 ( DISABLE SENSING + BACK OFF Y+0.1000" ) M05 G91 G00 Y+0.1000 G90 ( RAPID TO OPPOSITE SIDE: HOLE DIA 1.0000" - BACK OFF 0.1000" = 0.9000" ) G00 Y0.9000   ( PASS 1/2 — TOUCH Y+ ) G80 Y+ ( G192Y SETS Y TO HALF OF CURRENT Y VALUE — WIRE CENTER ) G192 Y ( DISABLE SENSING + BACK OFF Y-0.1000" ) M05 G91 G00 Y-0.1000 G90 G00 Y0.0000   ( PASS 2 — RETURN TO CURRENT CENTER BEFORE RE-TOUCHING ) G90 G00 X0.0000 Y0.0000   ( PASS 2/2 — TOUCH X- ) G80 X- ( SET X0 AT THIS SURFACE — NO RADIUS COMP, G192X WILL HALVE LATER ) G92 X0.0000 ( DISABLE SENSING + BACK OFF X+0.1000" ) M05 G91 G00 X+0.1000 G90 ( RAPID TO OPPOSITE SIDE: HOLE DIA 1.0000" - BACK OFF 0.1000" = 0.9000" ) G00 X0.9000   ( PASS 2/2 — TOUCH X+ ) G80 X+ ( G192X SETS X TO HALF OF CURRENT X VALUE — WIRE CENTER ) G192 X ( DISABLE SENSING + BACK OFF X-0.1000" ) M05 G91 G00 X-0.1000 G90 G00 X0.0000   ( PASS 2/2 — TOUCH Y- ) G80 Y- ( SET Y0 AT THIS SURFACE — NO RADIUS COMP, G192Y WILL HALVE LATER ) G92 Y0.0000 ( DISABLE SENSING + BACK OFF Y+0.1000" ) M05 G91 G00 Y+0.1000 G90 ( RAPID TO OPPOSITE SIDE: HOLE DIA 1.0000" - BACK OFF 0.1000" = 0.9000" ) G00 Y0.9000   ( PASS 2/2 — TOUCH Y+ ) G80 Y+ ( G192Y SETS Y TO HALF OF CURRENT Y VALUE — WIRE CENTER ) G192 Y ( DISABLE SENSING + BACK OFF Y-0.1000" ) M05 G91 G00 Y-0.1000 G90 G00 Y0.0000   ( FINAL RETURN TO CALCULATED CENTER ) G90 G00 X0.0000 Y0.0000